PVMD(1PVM)

NAME
pvmd, pvmd3 - PVM daemon

SYNOPSIS
pvmd [ -options ] [ hostfile ] &

DESCRIPTION
Pvmd3 is a daemon process which coordinates unix hosts in a virtual machine. One pvmd3 must run on each host in the group. They provide the communication and process control functions needed by the user's PVM processes. The daemon can be started manually with a host file argument that will automatically start the remote pvmds. The local and remote pvmds can also be started from the PVM console program pvm. The name of the daemon executable is pvmd3. It is usually started by a shell script, $PVM_ROOT/lib/pvmd. [v3.4 and later] Before running pvmd3, pvmd sources any commands in $HOME/.pvmprofile if this file exists.

OPTIONS
The following options may be specified on the command line when starting the master pvmd or PVM console:

-dmask
    Set pvmd debug mask. Used to debug the pvmd or libpvm (not intended to be used to debug application programs). Mask is the sum of the following bits and can be specified in hexadecimal (0x...), octal (0...) or decimal:
    Bit Information
    0x1 Packet routing
    0x2 Message routing and entry points
    0x4 Task state
    0x8 Slave pvmd startup
    0x10
        Host table updates
    0x20
        Select loop (below packet layer)
    0x40
        IP network
    0x80
        Multiprocessor nodes
    0x100
        Resource manager interface
    0x200
        Application (messages with no destination, etc.)
    0x400
        Wait contexts
    0x800
        Shared memory operations
    0x1000
        Semaphores
    0x2000
        Locks
    0x4000
        Message route control

-nname
    Specify an alternate hostname for the master pvmd to use. Useful when gethostname() returns a name not assigned to any network interface.

The following options are used by the master pvmd when starting slaves and are only of interest to someone writing a hoster. Don't just go using them, now.

-s  Start pvmd in slave mode. Hostfile cannot be used, five additional parameters must be supplied: master pvmd index, master IP, master MTU, slave pvmd index, and slave IP.

-S  Same as -s, but slave pvmd doesn't wait for its stdin to be closed after printing its parameters. Used for manual startup.

-f  Slave doesn't fork after configuration (useful if the slave is to be controlled or monitored by some process).

HOST FILE FORMAT
Each host in the virtual machine must have an entry in the host file. Lines beginning with a splat ( # ), optionally preceded by whitespace, are ignored. A simple host file might look like:
    # my first host file
    thud
    fred
    wilma
    barney
    betty This specifies the names of five hosts to be configured in the virtual machine. The master pvmd for a group is started by hand on the localhost, and it starts slaves on each of the remaining hosts using the rsh or rexec command. The master host may appear on any line of the host file. Host names cannot be numeric (IP) addresses, because they are passed to rsh and rexec(), which usually don't accept addresses. The simple format above works fine if you have the same login name on all five machines and the name of the master host in your .rhosts files on the other four. There are several host file options available:

    lo=NAME
        Specifies an alternate login name (NAME) to use.

    so=pw
        This is necessary when the remote host cannot trust the master. Causes the master pvmd to prompt for a password for the remote host in the tty of the pvmd (note you can't start the master using the console or background it when using this option) you will see:
            Password (honk.cs.utk.edu:manchek):
        you should type your password for the remote host. The startup will then continue as normal.

    dx=FILE
        Specifies the path of the pvmd executable. FILE may be a simple filename, an absolute pathname, or a path relative to the user's home directory on the remote host. This is mainly useful to aid in debugging new versions of PVM, but may have other uses.

    ep=PATH
        Specifies a path for the pvmd to search for executable program components when spawning a new process. The path may have multiple elements, separated by colons ( : ).

    wd=PATH
        Specifies a working directory in which all spawned tasks on this host will execute.

    sp=VALUE
        Specifies the relative computational speed of this host compared to other hosts in the configuration. VALUE is an integer in the range [1 - 1000000]

    bx=PATH
        Specifies the debugger program path. Note: the environment variable PVM_DEBUGGER can also be set.

    ip=NAME
        Specifies an alternate IP address to use for the host. As with host names (when ip= is not used), the address must be a host name, not a numeric address, because it is passed to rsh and rexec(). This option allows one to pick a specific network interface for a machine without using the interface's name. It can also be used to create a virtual machine using symbolic (instead of actual) host names.

    so=ms
        Rarely used. Causes the master pvmd to request user to manually perform the startup of a pvmd on a slave host when rsh and rexec network services are disabled but IP connectivity exists. See section "MANUAL STARTUP".

A dollar sign ( $ ) in an option introduces a variable name, for example $PVM_ARCH. Names are expanded from environment variables by each pvmd. Each of the flags above has a default value. These are:
    lo  The loginname on the master host.
    so  Nothing
    dx  $PVM_ROOT/lib/pvmd (or environment variable PVM_DPATH)
    ep  $HOME/pvm3/bin/$PVM_ARCH:$PVM_ROOT/bin/$PVM_ARCH
    wd  $HOME
    sp  1000
    bx  $PVM_ROOT/lib/debugger

You can change these by adding a line with a star ( * ) in the first field followed by the options, for example:
    * lo=afriend so=pw This sets new default values for 'lo' and 'so' for the remainder of the host file, or until the next '*' line. Options set on the last '*' line also apply to hosts added dynamically using pvm_addhosts(). Host options can be set without starting the hosts automatically. Information on host file lines beginning with '&' is stored, but the hosts are not started until added using pvm_addhosts(). Example host file:
	# host file for testing on various platforms
	fonebone
	refuge
	# installed in /usr/local here
	sigi.cs            dx=/usr/local/pvm3/lib/pvmd
	# borrowed accts, "guest", don't trust fonebone
	*                  lo=guest  so=pw
	sn666.jrandom.com
	cubie.misc.edu
	# really painful one, must start it by hand and share a homedir
	& igor.firewall.com  lo=guest2  so=ms  ep=bob/pvm3/bin/$PVM_ARCH

MANUAL STARTUP
When adding a host with this option set you will see on the tty of the pvmd:
	*** Manual startup ***
	Login to "honk" and type:
	$PVM_ROOT/lib/pvmd -S -d0 -nhonk 1 80a9ca95:0cb6 4096 2 80a95c43:0000
	Type response:
after typing the given command on host honk, you should see a line like:
	ddpro<2312> arch<ALPHA> ip<80a95c43:0a8e> mtu<4096>
type this line on the tty of the master pvmd. You should then see:
	Thanks
and the two pvmds should be able to communicate. Note you can't start the master using the console or background it when using this option.

OVERLOADING HOSTS
You can force PVM to overload a host (start more than one pvmd on it) by putting a '$' before the host name in the host file. This is not recommended unless you know what you're doing and have a good reason for it. You must build the PVM source with option OVERLOADHOST defined for it to work. You may also need to use the ip= hostfile option to define several names with the same IP address. If two or more hosts in a PVM have the same name, they cannot be identified uniquely.

STOPPING PVMD3
The preferred method of stopping all the pvmds is to give the halt command in the PVM console. This kills all PVM tasks, all the remote daemons, the local daemon, and finally the console itself. If the master pvmd is killed manually it should be sent a SIGTERM signal to allow it to kill the remote pvmds and clean up various files.

The pvmd can be killed in a manner that leaves the file /tmp/pvmd.uid behind on one or more hosts. Uid is the numeric user ID (from /etc/passwd) of the user. This will prevent PVM from restarting on that host. Deletion of this file will fix this problem:
    rm `( grep $user /etc/passwd || ypmatch $user passwd )
         | awk -F: '{print "/tmp/pvmd."$3; exit}'`

FILES
  $PVM_ROOT/lib/pvmd  PVM daemon startup script
  $PVM_ROOT/lib/$PVM_ARCH/pvmd3 PVM daemon executable
  $HOME/.pvmprofile Shell commands read by pvmd before
    running pvmd3
  $HOME/pvm3/bin/$PVM_ARCH  Private PVM executable directory
  $PVM_ROOT/pvm3/bin/$PVM_ARCH  System PVM executable directory
  /tmp/pvmd.uid Pvmd local socket address
  /tmp/pvml.uid Pvmd runtime error log
  $HOME/.rhosts File allowing access to a host from
    other hosts

SEE ALSO
pvm(1PVM), pvm_intro(1PVM), rhosts(5)